All-in-One Audio Editing Software for Windows
A useful all-in-one audio editor should handle the edits you make most often without making you switch apps for every cut. GiliSoft Audio Editor brings waveform selection, cutting, splitting, joining, mixing, recording, effects, and export into one Windows workspace.
Quick answer
Use GiliSoft Audio Editor when your job is to edit speech or music: open Audio Editing for waveform cuts and effects, use Joiner when clips should play in sequence, or Mix when sounds should overlap. Preview the result and use Export to save a new file. For batch format conversion rather than editing, use Audio Converter Ripper.
Before You Edit
- Keep the original recording and save the edited result under a new name.
- Listen to the source and mark the exact start, end, mistake, or pause you intend to change.
- Decide whether clips should play one after another (join) or at the same time (mix).
Choose the Right Audio Editor Tool
| Goal | Where to start | Check before export |
|---|---|---|
| Keep one excerpt | Audio Editing: cut unwanted opening and ending ranges | No word or note is cut at either edge |
| Remove a mistake | Audio Editing: select and cut the unwanted range | The remaining speech joins naturally |
| Combine complete clips | Joiner in the task hub | Every transition and track order is correct |
| Add music under narration | Mix in the task hub | The voice remains clear over the music |
| Smooth an opening or ending | Audio Editing: select a short range and open Effects | The fade starts and ends where intended |
| Adjust a quiet file's overall level | Audio Editing: Effects > Normalize | Compare the exported file with its source |
See the audio normalization guide for a complete file-level workflow and the difference between Normalize, Gain, and Compressor.
Edit an Audio File from Import to Export
- Choose the task
From the current task hub, open Audio Editing for waveform work, Joiner for clips in sequence, or Mix for overlapping sounds.
- Import and inspect
Open the source, play it, and identify the exact passage or files to change.
- Make the edit
In Audio Editing, select an unwanted waveform range, check its Start, End, and Duration, then use the scissors Cut control. For a clip excerpt, remove the unwanted opening and ending.
- Preview the result
Listen at each cut or transition. For an abrupt edge, select a short range and open Effects to apply a fade.
- Export and listen again
Use Export at the upper right, save a new file, and listen to the complete result outside the editor.
What Is in the Current Effects and View Menus?
The current Effects menu includes Gain, Fade In, Fade Out, Noise Reduction (Voice), EQ, Compressor, Normalize, Audio Repair, speed controls, and Remove Silence. Select the audio you intend to change, choose one effect at a time, then compare the result with the source. For a quiet file, follow the Normalize audio guide; for an opening or ending, see the fade guide.
View includes Frequency Analyser, Spectrum Analyser, Multitrack Mixer, Tempo Tools, and ID3 Tags. These are separate from editing effects; use them to inspect the recording or reach the relevant workspace.
Improve a Voice Recording with EQ
If a recording is audible but sounds muddy, thin, or harsh, the current Effects menu provides three EQ entries. Follow the voice EQ guide for selection, comparison, and export steps. EQ changes tone; use Noise Reduction (Voice) for a different noise problem. For a recording with alternating loud and quiet phrases, follow the voice volume and Compressor guide.
Change Audio Speed
For a faster or slower saved recording, select the whole file or a passage in Audio Editing and inspect the two speed-related entries in Effects. Use the audio speed guide to compare duration and pitch, preview the result, and export a new copy.
Review the Finished Audio
- Play a few seconds before and after every cut, join, or fade.
- Make sure speech and music stay balanced and nothing clips at the loudest point.
- Open the exported file outside Audio Editor and verify its complete playback and output format.
When to Choose a Different Tool
Audio Editor is designed for hands-on waveform editing and includes an optional Multitrack Beta workspace; do not assume it has the automation or plug-in chains of a full production suite. For batch format conversion, use GiliSoft Audio Converter Ripper. For a wider set of separate audio utilities, see GiliSoft Audio Toolbox.
Frequently Asked Questions
How do I save one excerpt?
In Audio Editing, cut the unwanted opening and ending from a source copy, then use Export to save the remaining clip under a new name.
What is the difference between joining and mixing?
Joining plays clips one after another. Mixing layers two sounds so they play at the same time. The current task hub has separate Joiner and Mix entries.
Can I record and edit in the same app?
Yes. The task hub includes Audio Recorder and Audio Editing. Check the recording source and level, then open the result for editing.
How do I avoid an abrupt cut?
Move the cut to a quieter point, preview both sides, and apply a short fade if the transition still sounds sudden.